[MVRC] Mantium Virtual Racecar Challenge 2017

[variante]

Awesome, Gary and Matteo! Looking forward to seeing the car running on track!

Great news, Andre'. Now I need to win the last race to have my car featured on the magazine

[LVDH]

Great news, Andre'. Now I need to win the last race to have my car featured on the magazine

A season without you winning a race would be a bit strange.

In case somebody overlooked: The last race will be delayed one week.

[rjsa]

That'll be December 10th?

[CAEdevice]

Great news, Andre'. Now I need to win the last race to have my car featured on the magazine

A season without you winning a race would be a bit strange.

Not as strange as a season without a 4th place by CAEdevice.
In 2016 LeMans has been my worst race, I hope to do better this year.

[roon]

I imagine from a structural point of view this rear wing wouldn't cope too well, with a lack of strut bearing the load. Looks epic though!

Yes, it is an (extreme) high downforce airfoil coupled with the (extreme) low downforce pillars... but for a graphic AC model it could be acceptable (maybe you can increase the dimension of the pillars section, to have a more realistic geometry).

Maybe add some short connectors between the pontoons and the pillars.

[garyjpaterson]

I imagine from a structural point of view this rear wing wouldn't cope too well, with a lack of strut bearing the load. Looks epic though!

Yes, it is an (extreme) high downforce airfoil coupled with the (extreme) low downforce pillars... but for a graphic AC model it could be acceptable (maybe you can increase the dimension of the pillars section, to have a more realistic geometry).

Maybe add some short connectors between the pontoons and the pillars.

Something a bit like this was my thought. Apologies for the render, not imported it ingame yet.

[roon]

Yes, it is an (extreme) high downforce airfoil coupled with the (extreme) low downforce pillars... but for a graphic AC model it could be acceptable (maybe you can increase the dimension of the pillars section, to have a more realistic geometry).

Maybe add some short connectors between the pontoons and the pillars.

Something a bit like this was my thought. Apologies for the render, not imported it ingame yet.

https://i.imgur.com/v15aEYDh.jpg
https://i.imgur.com/dJUcLPLh.jpg

Yeah. Was thinking of what's sometimes found on the ends F1 RWs.

[garyjpaterson]

Bit of branded tyres never did any harm

[LVDH]

Yeah, Mantium issued standard tires. Very cool...

[darkpino]

So i finally have some time to figure this all out...
I read the readme, i think i installed it the proper way but then: i use the webapplication to make myself a front wing, rear wing and floor. But in which map should i put them? Ive put them in 'special_bc' but seems thats not allowed...

[Alonso Fan]

So i finally have some time to figure this all out...
I read the readme, i think i installed it the proper way but then: i use the webapplication to make myself a front wing, rear wing and floor. But in which map should i put them? Ive put them in 'special_bc' but seems thats not allowed...

Either high res surfaces or vehicle body

Special bc is for engine inlets and exhausts

[darkpino]

That did work, thanks!
when i click 'build case' it says: warning: no front wheels detected and after that i click 'run case' nothing happens. When i click post-process case it says i need to run the case first?

[Alonso Fan]

That did work, thanks!
when i click 'build case' it says: warning: no front wheels detected and after that i click 'run case' nothing happens. When i click post-process case it says i need to run the case first?

Ah you need the cfd parts file from the challenge page. It should have wheels as separate stl files, as well as suspension etc

You'll need two extra folders in the case structure called frt_wheels and rr_wheels.

If I remember correctly wheels 1 and 2 are the fronts.

Suspensions can go in vehicle body

After you've done all this go to your parent case directory and delete everything except input_files

Create the case again

[darkpino]

Thanks! no more errors now! Only when clicking 'run case' nothing happens and at post process case it gives me the error to first run the case

[Alonso Fan]

Thanks! no more errors now! Only when clicking 'run case' nothing happens and at post process case it gives me the error to first run the case

No problem

You need to run the case manually

Are you running Windows?